Lenovo RackSwitch G8264CS Скачать руководство пользователя страница 57

Страница: 57 / 96

Chapter 3: Installing G8264CS Hardware and Options

Class 1 Laser Product
Laser Klasse 1
Laser Klass 1
Luokan 1 Laserlaite
Appareil À Laser de Classe 1

To install a transceiver in an Omni Port, complete the following steps.

Note:

To avoid damage to the cable or the transceiver, do not connect the cable

before you install the transceiver.

1. Remove the safety cap and pull the locking lever into the down (unlocked)

position.

2. Insert the transceiver into the port until it clicks into place. Use minimal

pressure when you insert the transceiver into the slot. Do not use excessive

force when you insert the transceiver or you might damage the transceiver or

the Omni Port slot.
The transceiver has a mechanical guide key to prevent you from inserting the
transceiver in an incorrect orientation.

3. Pull up the locking lever to lock the transceiver into place.
4. Connect the cable following the

“Cabling Guidelines” on page 38

. Use a

fiber-optic cable for optical transceivers.

To remove the transceiver, disconnect the cable, and pull down the locking lever to

release the transceiver. After you remove the transceiver, replace the safety cap.

Содержание RackSwitch G8264CS

































































































Результаты поиска

Содержание RackSwitch G8264CS

Отзывы:

Похожие инструкции для RackSwitch G8264CS

Бренды по названию

Популярные бренды

Lenovo RackSwitch G8264CS, Руководство по установке

Результаты поиска

Содержание RackSwitch G8264CS

Отзывы:

Похожие инструкции для RackSwitch G8264CS

Бренды по названию

Популярные бренды