Lenovo RackSwitch G8264CS Скачать руководство пользователя страница 55

Страница: 55 / 96

Chapter 3: Installing G8264CS Hardware and Options

3. Pull up the locking lever to lock the transceiver into place.
4. Connect the fiber-optic cable following the

“Cabling Guidelines” on page 38

To remove an SFP+ optical transceiver, disconnect the fiber-optic cable, and pull

down the locking lever to release the transceiver. After you remove the transceiver,

replace the safety cap.

Installing a QSFP+ Optical Transceiver

The QSFP+ ports accept approved QSFP+ transceivers. The QSFP+ optical

transceiver provides an MTP cable connector for connecting to external ports.

Statement 3

CAUTION:
When laser products (such as CD-ROMs, DVD drives, fiber optic devices, or
transmitters) are installed, note the following:

•

Do not remove the covers. Removing the covers of the laser product could
result in exposure to hazardous laser radiation. There are no serviceable
parts inside the device.

•

Use of controls or adjustments or performance of procedures other than
those specified herein might result in hazardous radiation exposure.

DANGER

Class 1 Laser Product
Laser Klasse 1
Laser Klass 1
Luokan 1 Laserlaite
Appareil À Laser de Classe 1

Some laser products contain an embedded Class 3A or Class 3B laser
diode. Note the following.

Laser radiation when open. Do not stare into the beam, do not view directly
with optical instruments, and avoid direct exposure to the beam.

Содержание RackSwitch G8264CS

































































































Результаты поиска

Содержание RackSwitch G8264CS

Отзывы:

Похожие инструкции для RackSwitch G8264CS

Бренды по названию

Популярные бренды

Lenovo RackSwitch G8264CS, Руководство по установке

Результаты поиска

Содержание RackSwitch G8264CS

Отзывы:

Похожие инструкции для RackSwitch G8264CS

Бренды по названию

Популярные бренды