Lenovo RackSwitch G8264CS Скачать руководство пользователя страница 39

Страница: 39 / 96

Chapter 3: Installing G8264CS Hardware and Options

Installing the G8264CS in a Rack

The G8264CS can be rack-mounted using one of the following mounting kits:
•

For a standard 19-inch equipment rack, use the 2-post rack mounting brackets
and screws included with the switch. Installation instructions begin on

page 39

•

For a Lenovo System x

or Power 4-post rack, use the Lenovo Adjustable 19”

4-Post Rail Kit. This kit must be purchased separately. Installation instructions
begin on

page 41

•

For a Lenovo iDataPlex

rack, use the iDataPlex mounting kit. This kit must be

purchased separately. Installation instructions begin on

page 45

Installing the G8264CS in a Standard Equipment Rack

This section describes how to install the G8264CS in a standard 19-inch equipment

rack using the mounting kit included with the switch. For information about mounting

the switch in other supported racks, see the appropriate section in this chapter.

The following parts are included in the standard mounting kit.

Attention:

The rack-mounting frame may be unable to support the weight of the

switch with only the front post mounting brackets (2-post application). If the switch
has an undesirable amount of sag, it is recommended to use a 4-post mounting kit.

Attention:

For earthquake stability, mount the switch in a 4-post rack.

Statement 26

CAUTION:
Do not place any object on top of rack-mounted devices.

Table 11. 2-post rack mount kit parts

Item number

Description

Quantity

Mounting brackets

M4 screws

M6 screws

M6 clip nuts

M6 cage nuts

M6 locking washers

Содержание RackSwitch G8264CS

































































































Результаты поиска

Содержание RackSwitch G8264CS

Отзывы:

Похожие инструкции для RackSwitch G8264CS

Бренды по названию

Популярные бренды

Lenovo RackSwitch G8264CS, Руководство по установке

Результаты поиска

Содержание RackSwitch G8264CS

Отзывы:

Похожие инструкции для RackSwitch G8264CS

Бренды по названию

Популярные бренды