Lenovo RackSwitch G8264CS Скачать руководство пользователя страница 63

Страница: 63 / 96

Chapter 4: Removing and Replacing G8264CS Components

To replace a hot-swap power supply module, complete the following steps:
1. Select an empty power supply module bay on the rear of the switch. If the

target bay is protected by a blank power filler plate, remove the blank.

2. Insert the power supply module into the selected power-supply bay and gently

push it into the slot until it latches. Each power supply module has a

mechanical guide key to prevent you from inserting the module incorrectly.

3. Connect the power cord to the power supply module and to an appropriate

universal grounded AC power source.

4. Make sure that the power supply module’s DC and ~AC LEDs are green.

Removing and Replacing a Fan Module

The rear panel of the G8264CS has four bays for hot-swap fan modules. Four active

fan modules are required for redundancy.

With active fan modules in all fan bays, if one fan fails, the switch will send an error

message and continue operation. You can then replace the failed fan without

powering off the switch or disrupting switch functions. If a second fan fails, the

switch will send another error message, write a log message to flash memory, and

shut down to prevent overheating.

For proper airflow when operating the switch with one empty fan bay (a

non-redundant configuration), the empty fan bay must be closed with a blank fan

filler plate.

Removing the Fan Module

To remove a hot-swap fan module, complete the following steps:
1. Loosen the retainer screw.
2. Grasp the extractor handle and gently pull the fan module from the slot.

Retainer Screw

Содержание RackSwitch G8264CS

































































































Результаты поиска

Содержание RackSwitch G8264CS

Отзывы:

Похожие инструкции для RackSwitch G8264CS

Бренды по названию

Популярные бренды

Lenovo RackSwitch G8264CS, Руководство по установке

Результаты поиска

Содержание RackSwitch G8264CS

Отзывы:

Похожие инструкции для RackSwitch G8264CS

Бренды по названию

Популярные бренды