Lenovo RackSwitch G8264CS Скачать руководство пользователя страница 65

Страница: 65 / 96

Chapter 4: Removing and Replacing G8264CS Components

Removing the G8264CS from a Standard Equipment Rack

This section describes how to remove the G8264CS from a standard 19-inch

equipment rack. For information about removing the switch from other supported

racks, see the appropriate section in this chapter.

To remove the G8264CS from a standard rack, complete the following steps:
1. Disconnect all external cables.
2. If the air-duct option has been installed, remove it as described in

“Removing

the Air-Duct Option” on page 70

3. Loosen and remove M6 screws, washers, and clip nuts (or cage nuts) to

release the switch unit from the rack.

4. Slide the switch unit out of the rack.
5. Loosen and remove the M4 screws attaching the mounting bracket on each

side of the switch.

6. If replacing the unit with another G8264CS, see

“Replacing the G8264CS” on

page 71

Содержание RackSwitch G8264CS

































































































Результаты поиска

Содержание RackSwitch G8264CS

Отзывы:

Похожие инструкции для RackSwitch G8264CS

Бренды по названию

Популярные бренды

Lenovo RackSwitch G8264CS, Руководство по установке

Результаты поиска

Содержание RackSwitch G8264CS

Отзывы:

Похожие инструкции для RackSwitch G8264CS

Бренды по названию

Популярные бренды