Lenovo RackSwitch G8264CS Скачать руководство пользователя страница 52

Страница: 52 / 96

G8264CS Installation Guide

Installing Port Transceivers

The G8264CS supports copper and optical transceivers.

To install a supported transceiver, see the following sections:
•

“Installing an SFP Copper Transceiver” on page 52

•

“Installing an SFP Optical Transceiver” on page 52

•

“Installing an SFP+ Optical Transceiver” on page 54

•

“Installing a QSFP+ Optical Transceiver” on page 55

•

“Installing an Omni Port Optical Transceiver” on page 56

Installing an SFP Copper Transceiver

Approved 1 GbE SFP copper transceivers are supported in G8264CS SFP+ port

slots and in some breakout adapters that can be installed in QSFP+ port slots. The

SFP copper transceiver provides an RJ-45 connector that accepts a standard

10/100/1000BASE-T (Category 5) cable.

To install an SFP copper transceiver in an SFP+ port slot on the switch or in an

installed QSFP+ breakout adapter, complete the following steps.

Note:

To avoid damage to the cable or the SFP transceiver, do not connect the

cable before you install the transceiver.

1. Remove the safety cap and pull the locking lever into the down (unlocked)

position.

2. Insert the transceiver into the slot until it clicks into place. Use minimal pressure

when you insert the transceiver. Do not use excessive force when you insert

the transceiver or you might damage the transceiver or the slot.
The transceiver has a mechanical guide key to prevent you from inserting the
transceiver in an incorrect orientation.

3. Pull up the locking lever to lock the transceiver into place.
4. Connect the cable following the

“Cabling Guidelines” on page 38

To remove an SFP copper transceiver, disconnect the cable, and pull down the

locking lever to release the transceiver. After you remove the transceiver, replace

the safety cap.

Installing an SFP Optical Transceiver

Approved 1 GbE SFP optical transceivers are supported in G8264CS SFP+ port

slots and in some breakout adapters that can be installed in QSFP+ port slots. The

SFP optical transceiver provides two fiber-optic cable connectors for connecting to

external ports.

Содержание RackSwitch G8264CS

































































































Результаты поиска

Содержание RackSwitch G8264CS

Отзывы:

Похожие инструкции для RackSwitch G8264CS

Бренды по названию

Популярные бренды

Lenovo RackSwitch G8264CS, Руководство по установке

Результаты поиска

Содержание RackSwitch G8264CS

Отзывы:

Похожие инструкции для RackSwitch G8264CS

Бренды по названию

Популярные бренды