Lean ROBOTIQ AX Series Скачать руководство пользователя страница 65

Страница: 65 / 112

Color and

signal type

Condition status

Cause or action needed (troubleshooting for e-Series)

RED

Fast blink

The linear axis controller (PLC) is unable to
communicate with the Robot controller (UR).

The robot has been started and needs time to boot up
(Polyscope has not loaded yet)

Make sure your Ethernet/USB adapter is properly
connected: the LED on the Ethernet adapter should be
ON.

Make sure the Ethernet cable between the PLC and
robot controller is properly connected (to the USB
adapter) .

Try pressing the Scan button in the installation tab.

Try powering off the system (both the robot and the
linear axis Controller). Wait 1 minute. Power up the
system again.

RED

Slow blink

Communication between the robot and the
linear axis controller (PLC) is established, but
Copilot has not established the communication
yet with the linear axis controller.

Tap Installation

→

URCaps

→

Copilot

→

Linear Axis

and click on Scan button.

RED

Solid

An axis error happened.

Tap Installation

→

URCaps

→

Copilot

→

Linear Axis.

Then, check the error message and act accordingly.

RED

Solid

A Protective or Emergency stop has occurred.

Follow the procedures required by the system to recover
from either a Protective or Emergency stop.

YELLOW

Solid

When the Scan has succeeded, but the axis
brakes are not released
(Start not done yet)

A program is running without Palletizer node.

Tap Installation

→

URCaps

→

Copilot

→

Linear Axisand

click on Start button. You may need to press the
safeguard reset button (if you have one in your specific
safety setup).

YELLOW

Slow blink

A Safeguard Stop has occured.

Press the safeguard reset button.

BLUE

Solid

The pallet is complete or missing;

AND

The system is palletizing on the other side.

Place a new pallet

Содержание ROBOTIQ AX Series

















































































































Результаты поиска

Содержание ROBOTIQ AX Series

Отзывы:

Похожие инструкции для ROBOTIQ AX Series

Бренды по названию

Популярные бренды

Lean ROBOTIQ AX Series, Инструкция по эксплуатации

Результаты поиска

Содержание ROBOTIQ AX Series

Отзывы:

Похожие инструкции для ROBOTIQ AX Series

Бренды по названию

Популярные бренды