Label NEPTIS/LE Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 40

background image

15) LIST OF PARAMETERS TO SELECT FOR THE CONTROL UNITS

DIP-SWITCH S1

SLAVE

MASTER

DIP 1 = PUSH & GO

DIP 2 = WIND STOP

DIP 3 = CYCLIC FUNCTION (repeated opening and closing)

DIP 4 = ELECTRO-LOCK OPERATING MODE

DIP 5 = CLOSING BY SPRING AND MOTOR

DIP 6 = INITIAL SET-UP

DIP 7 = DOOR OPEN/NIGHT LOCK (with function selector switch on II)

DIP 8 = COURTESY MODE FOR THE DISABLEDI

DIP 9 = 10 sec OPENING WITH “NIGHT LOCK” WORK PROGRAM

DIP 10 = AUTOMATIC INCREASE OF THE HOLD TIME

DIP 11 = SELECTION OF THE FUNCTION SELECTOR DEVICE

DIP 12 = ADJUSTMENT OF FUNCTIONS & POTENTIOMETERS VIA SELECTOR

DIP-SWITCH S2

DIP 1 = STEPPING MODE

DIP 2 = ELECTRO-LOCK RELEASE IN FREE DOOR MODE

DIP 3 = PEDESTRIAN OPENING WITH FREE DOOR (OFF)/NIGHT LOCK (ON)

DIP 4 = PEDESTRIAN OPENING FUNCTION

DIP 5 = WING DELAY ON STARTING

DIP 6 = MASTER/SLAVE CONTROL UNIT SET-UP

DIP 7 = “DOUBLE-WING DOOR ” OPERATING MODE

DIP 8 = PHOTOCELL OPERATING MODE

DIP 9 = PHOTOCELL OPERATING MODE

DIP 10 = OPERATION OF THE RADAR INPUTS

DIP 11 = RESETTING OF TECHNICAL MENU DEFAULT VALUES (see TECHNICAL MENU)

DIP 12 = CONTROL UNIT RESET

33

14) PEDESTRIAN OPENING

The pedestrian opening function can only be used for a swing door with two wings. It is therefore essential for the actuators
to be set up for operation as a DOUBLE-WING DOOR (see sect.13).
To enable the PEDESTRIAN OPENING function, set dipswitch 4 of S2 ON and select the condition which activates the
function by means of dipswitch 3 of S2.

A)

DIP 3 S2

DIP 4 S2

OFF

ON

Choose on the program selector to enable the PEDESTRIAN OPENING function.

- The status loses its original free door function in this condition.

B)

DIP 3 S2

DIP 4 S2

ON

ON

Choose on the program selector to enable the pedestrian opening FUNCTION.

- The status loses its original mìnight lock function in this condition.

In both case A) and B), activation of an internal or esternal RADARinput partially opens the door, i.e. the sole wing
controlled by the MASTER actuator (pedestrian wing), while the START or EMERGENCY inputs open both MASTER and
SLAVE wings.
manual pushing with the push & go function only opens the pedestrian wing.

SLAVE

MASTER

PARAMETERS

«
...
31
32
33
34
35
...
»

Содержание NEPTIS/LE









































Отзывы:

Нет отзывов

Похожие инструкции для NEPTIS/LE

Бренд: CAME Страницы: 104

Бренд: Eco Страницы: 10

Бренд: Eco Страницы: 112

Бренд: MAC TOOLS Страницы: 30

Бренд: Omega Страницы: 16

Бренд: HURNER Страницы: 69

Бренд: Cebora Страницы: 26

iMotion 1302.KI

Бренд: Tormax Automatic Страницы: 20

Бренд: Hitbox Страницы: 18

Aristo Mig 3001i

Бренд: ESAB Страницы: 76

Бренд: Migatronic Страницы: 44

Бренд: SPT Plasmateknik AB Страницы: 15

VARMIG 231-i LCD

Бренд: Daihen varstroj Страницы: 100

Бренд: Parweld Страницы: 17

Бренд: Viessmann Страницы: 44

Бренд: Hitachi Страницы: 44

Бренд: Jasic Страницы: 30

Бренд: Jasic Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды