Label NEPTIS/LE Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 40

background image

11

9.0 ARM REMOVAL

Warning:

Strictly comply with the steps described when removing the arms. Only remove the screw that fixes the tapering pin and
tighten the puller nut when specified in the instructions. Removal of the screw that fixes the tapered pin and use of the puller
nut may cause the pulleys and gears in the actuator to move unless the closing spring has been previously locked.
Keep your fingers and other parts of the body well away from the moving parts during this operation!

9.1 How to restore the standard preload and lock the spring

Before you remove the arm, you must restore the spring load to its
standard value, whereby the red mark on the belt matches the red
mark on the pulley (see figure alongside), and lock the spring in this
position. To do this, move the door by hand until this condition has
been obtained and the red marks on the belt and pulley match.

Move the locking screw from the free position to the locked position
and make sure that the screw fits into the locking hole in the pulley.

9.2 How to extract the tapering pin

Remove the fixing screw from the tapering pin.

Tighten the release nut upwards until the pin has been completely
removed.

LOCKED

BELT
REFERENCE

PULLEY
REFERENCES

«
...
9
10
11
12
13
...
»

Содержание NEPTIS/LE









































Отзывы:

Нет отзывов

Похожие инструкции для NEPTIS/LE

Бренд: Laars Страницы: 14

Бренд: Jasic Страницы: 18

Бренд: ESAB Страницы: 34

Бренд: iWeld Страницы: 36

Smarty 4X P Series

Бренд: Salda Страницы: 30

L2.00 AC/DC Expert 3.0 TIG

Бренд: EWM Страницы: 82

RIRS 400HE EKO 3.0

Бренд: Salda Страницы: 34

Бренд: fadini Страницы: 12

Бренд: Worldwel Страницы: 5

Бренд: INVERTEC Страницы: 36

Бренд: ims PRO Страницы: 114

Бренд: Panasonic Страницы: 23

Бренд: Panasonic Страницы: 60

Бренд: Panasonic Страницы: 64

Norton 9540 Series

Бренд: Assa Abloy Страницы: 16

Бренд: Assa Abloy Страницы: 4

Бренд: Assa Abloy Страницы: 4

Бренд: Assa Abloy Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды