Label NEPTIS/LE, Руководство по установке

Страница: 6 / 40

6
3.0 GENERAL SAFETY RECOMMENDATIONS
Only begin to install the actuator after you have carefully read this instruction manual.
Both the mechanical part and the electrical part must be installed in a perfectly workmanlike manner, in compliance with
the current laws in force. Failure to comply with these latter may result in danger hazards for persons or property.
The installer must be a competent person who has been adequately trained. He must check to make sure that the structure
on which the actuator is installed is strong and stable. If necessary, structural modifications must be made to strengthen it.
The installer must also check that all zones where there is a risk of crushing, dragging, shearing or other dangers, are
protected by means of electronic safety devices, safety freeboards or barriers. These devices must be installed in
compliance with the current laws and in a perfectly workmanlike way, also in relation to the place of use, the type of use and
the operating logic of the product. The forces developed by the complete system as it operates must comply with the current
standards and, where this is not possible, the zones affected by these forces must be protected with electronic safety devices.
Moreover, dangerous zones must be indicated, as established by the current laws in force.
Before the actuator is connected, make sure that the electricity main possesses characteristics that are compatible with those
described in the technical specifications of this manual, and that there is a differential circuit-breaker and adequate
protection against overcurrents on the supply side of the system. Remember to turn off the power supply before installing or
servicing the actuator and whenever the cover must be opened.
Electrostatic charges can damage the electronic components on the boards. Wear a grounded antistatic bracelet if you
must work on the electronic boards. Never place the hands or other parts of the body in moving parts, such as belts, pulleys,
gears, etc.
Servicing the actuator is of fundamental importance if the system is to operate correctly and safely. Comply with the
manufacturer’s instructions described in this manual when servicing the actuator.
The manufacturer declines all liability for improper installation or use of the product, or for damage deriving from
unauthorized modifications to the system. Only use genuine spare parts if replacements or repairs are required. The
manufacturer cannot be held liable for the way the doors or gates to be automated are constructed, or for damages caused
by failure to build the doors and gates in compliance with good workmanlike techniques.
Protection degree IP22 requires that the actuator only be installed inside buildings. The manufacturer declines all liability
for damage caused by assembly on the outside, without adequate protections.
Always make sure that the product is in a good condition before it is installed.
This product cannot be installed in places with an explosive atmosphere or in the presence of inflammable fumes or gases.
This product must be disposed of according to the current laws in force at the end of its useful life.
Do not leave parts of the product or its packaging within children’s reach, as they could become a danger hazard.
4.0 MACHINE DIRECTIVE
5.0 INSTRUCTIONS FOR USE
As established by the EU commission, automated pedestrian closing systems are governed by the machine directive
(98/37/EC). This latter specifies that the installer who fits a driving system on a door or gate has the same obligations as the
manufacturer of the machine. Thus, he must:
1. Prepare the technical report (complete with the documents described in annex V of the Machine Directive).
2. Compile the relative CE conformity certificate (as per annex II-A of the Machine Directive).
3. Affix CE marking to the motorized door or gate (1.7.3, of annex I of the Machine Directive).
The installer must keep the technical report at the disposal of the competent authorities in the country for at least 10 years,
running from the date on which the motorized door or gate was manufactured.
The installer must consign the following documents to the customer:
1. Instructions on how to operate and safely use the system.
2. The routine maintenance instructions.
3. The declaration of conformity.
4.
The maintenance register.
The "NEPTIS/LE” actuator is suitable for continuous service. The maximum weight of the wing it drives depends on the
actual wing itself, on the type of arm and on the type of fixing mechanism (POWER or SPEED).
Consult the tables in chapter 6, depending on the application used.
The specifications described above refer to a typical installation and may be substantially influenced by the variables in
every installation, euch as friction, balancing, environmental conditions, etc.