background image

DIP SWITCH S2

"NEPTIS/LE”

CONTROL UNIT

(to be set with

digital selector)

DIP SWITCH

SW1

PHOTOCELL

BOARD

DIP8

DIP9

DIP1

DIP2

OFF

ON

OFF

ON

ON

ON

ON

OFF

ON

ON

OFF

ON

ON

OFF

OFF

ON

ON

ON

ON

ON

NUMBER OF PHOTOCELLS INSTALLED AND THEIR USE

1 CLOSING SAFETY PAIR (FT3/FR3)

1 PAIR AS OPENING CONTROL (FT1/FR1)

(FT1/FR1 & FT2/FR2)

PAIRS AS OPENING CONTROL 

(FT1/FR1)

and 1 CLOSING SAFETY PAIR (FT3/FR3)

PAIR AS OPENING CONTROL 

(FT1/FR1 & FT2/FR2)

and 1 CLOSING SAFETY PAIR (FT3/FR3)

PAIRS AS OPENING CONTROL 

OPERATING MODE OF THE PAIRS OF PHOTOCELLS

FT1/FR1

: same operation as the INTERNAL RADAR input.

FT2/FR2

: same operation as the EXTERNAL RADAR input.

FT3/FR3

: safety photocell. Operates during the closing phase, by reversing the direction of the door.

TABLE 12.1

SENSITIVITY ADJUSTMENT

Once  the  pohotocells  have  been  positioned,  their  sensitivity  must  be 
regulated by means of the potentiometer on the board. Proceed in the 
following way:
1) Calibrate the potentiometer depending on the distance between the 

photocells (see figure alongside).

2)  If the leds on the phtocells are off, their sensitivity is correct.
3)  If the leds are on, slowly turn the potentiometer towards its maximum 

setting until the leds go out. 

4)  Check to make sure that the relative leds come on by breaking the 

infrared beam of the photocells.

MIN. POTENTIOM.

SETTING

up to 2 meters

POTENTIOMETER

HALFWAY

2 to 4 meters

MAX. POTENTIOM.

SETTING

4 to 6 meters

MIN
SENSITIVITY

MAX

SENSITIVITY

DIP SWITCH SW1

L1 L2 L3

RECEIVER AND TRANSMITTER CONNECTIONS

To avoid interference due to direct sunlight, the receivers should be installed on the more sheltered side.

Terminal board  M5 ( FT1 - FT2 - FT3- + )

FT3   =  TRANSMITTER 3 input ( BLACK WIRE)

FT2   =  TRANSMITTER 2 input ( BLACK WIRE) 

FT1   =  TRANSMITTER 1 input ( BLACK WIRE)
 
   +   =  POWER SUPPLY FOR ALL THE TRANSMITTERS (BLUE WIRES)

Terminal board  M6 ( FR1 - FR2 - FR3- VCC -  GND )

FR3   = RECEIVER 3 input (BROWN WIRE)) 

FR2   = RECEIVER 2 input (BROWN WIRE))  

FR1   = RECEIVER 1 input (BROWN WIRE)) 

VCC  = ( + )  POWER SUPPLY FOR ALL THE RECEIVERS (BLUE WIRES)

GND = ( - )  POWER SUPPLY FOR ALL THE RECEIVERS (BLACK WIRES)

FR3
FR2

FR1

VCC

GND

M6

FT3

FT2

FT1

+

M5

29

Содержание NEPTIS/LE









































Отзывы: