Label NEPTIS/LE Скачать руководство пользователя страница 2

Страница: 2 / 40

Manufacturer:

Label S.p. A.

Address:

via Ilariuzzi 17/A- 43100 San Pancrazio Parmese. PARMA- ITALY

Declares that:

the

NEPTIS/LE

actuator for swing doors

has been designed to be built into machinery or to be assembled with other devices so as to form
machinery covered by Machine

Directive 98/37/EC and that it conforms to the essential safety requirements of the following
directives:

Low Voltage Directive 73/23/EEC and successive modification 93/68/EEC

Electromagnetic compatibility Directive 89/336/EEC and successive modifications 92/31/EEC
and 93/68/EEC

LABEL S.p.A.

Sede: ITALY - 43100 PARMA - S. Pancrazio P.se - Via Ilariuzzi, 17/A
Tel. (+39) 0521/6752 - Fax (+39) 0521/675222
[email protected] - web: www.labelspa.it

Parma, 15/06/2006

The President

Bruno Baron Toaldo

DECLARATION OF CONFORMITY

Содержание NEPTIS/LE









































Результаты поиска

Содержание NEPTIS/LE

Отзывы:

Похожие инструкции для NEPTIS/LE

Бренды по названию

Популярные бренды

Label NEPTIS/LE, Руководство по установке

Результаты поиска

Содержание NEPTIS/LE

Отзывы:

Похожие инструкции для NEPTIS/LE

Бренды по названию

Популярные бренды