Label NEPTIS/LE Скачать руководство пользователя страница 34

Страница: 34 / 40

TECHNICAL MENU

3) NOT USED

4) NOT USED

5) END OF TRAVEL DISTANCE ON OPENING

6) PUSHING POWER AT END OF OPENING MANOEUVRE

7) PUSHING POWER AT END OF CLOSING MANOEUVRE ("NEPTIS/LE” version only)

8) NOT USED

9) PUSHING TIME AT END OF CLOSING MANOEUVRE ("NEPTIS/LE” version only)

10) SLOWING DISTANCE ON OPENING

11) SLOWING DISTANCE ON CLOSING

12) WINF STOP FORCE INTENSITY ON OPENING

13) WING DELAY ON START-UP IN OPENING PHASE

14) WING DELAY ON START-UP IN CLOSING PHASE

SLAVE

MASTER

PARAMETERS

POTENTIOMETERS

TM1 = O0PENING SPEED

TM2 = CLOSING SPEED

TM3 = OPENING SAFETY SENSOR CUT-OUT DISTANCE

TM4 = PUSHING POWER LIMITATION

TM5 = HOLD TIME

TM6 = UPKEEP VOLTAGE ON CLOSING

TM7 = WIND STOP FORCE INTENSITY

TM8 = PUSH & GO ACTIVATION DISTANCE

TM9 = INTENSITY OF FINAL CLOSING PUSH TO LINK ELECTRO-LOCK

TM10 = POWER OF CLOSING STROKE FOR RELEASING ELECTRO-LOCK

16) MEANINGS OF THE BUZZER SIGNALS (BEEPS)

5 BEEPS = control unit without initial set-up (press START with function selector switch in 0 position)
Long BEEP

= control unit without initial set-up (keeping

START depressed with function selector switch on I or II)

6 BEEPS = ENCODER not operating or disconnected
1 BEEP

= programming procedure accessed via digital selector

1 BEEP = programming procedure quitted via digital selector

without

memorizing the data

2 BEEPS = programming procedure quitted via digital selector

with

data memorized

1 long BEEP (5”)= initial set-up terminated.

17) TECHNICAL SPECIFICATIONS

POWER SUPPLY

/- 10%

Max. POWER EXT. ACCESSORIES

20W

TIPE OF OPERATION

Intensive use

OPERATING TEMPERATURE

-20°C / +50°C

PROTECTION DEGREE

IP22

SLAVE

MASTER

1) PUSHING FORCE AT THE BEGINNING OF THE CLOSING MANOEUVRE (on closing)

2) DISTANCE AT THE BEGINNING OF THE CLOSING MANOEUVRE (on closing)

Содержание NEPTIS/LE









































Результаты поиска

Содержание NEPTIS/LE

Отзывы:

Похожие инструкции для NEPTIS/LE

Бренды по названию

Популярные бренды

Label NEPTIS/LE, Руководство по установке

Результаты поиска

Содержание NEPTIS/LE

Отзывы:

Похожие инструкции для NEPTIS/LE

Бренды по названию

Популярные бренды