Laars MASCOT LX Скачать руководство пользователя страница 23

Страница: 23 / 94

Mascot LX Service Manual

Installer and Service Mode Displays

Changing Installer Settings -

The SIT controller allows you to change a number of operating param-

eters using the Installer mode. Once a unit has been set up and operat-

ing normally, you should not need to change any of the Installer settings.

These have been included for use during setup, or to handle special

situations. For a complete list of Installer parameters, see Section App1

in the Appendix.
Here is the procedure for changing a setting:
1. To go to Installer mode, press the OK/Select and Down buttons at

the same time for five seconds. You should see “U00” to indicate

you have entered Installer mode.

2. Press OK/Select again. The display will blink.

3. Use the Up button to change the value to “15,” then press OK/Select

again.

4. Use the Up and Down buttons to go to the parameter you want to

change.

5. Press OK/Select to indicate you want to change that parameter. The

display will blink.

6. Use the Up and Down buttons to change the value.

7. Press the OK/Select button to save the new value, or Cancel to

leave the old value.

8. Press and hold OK/Select for 3 seconds to leave Installer mode.

Service Mode -

The Service mode should only be used by a technician who has been

trained by Laars. Service mode is used to set the “high fire” and “low

fire” conditions during CO

testing. For details, see Section C2.

Service mode symbol

Содержание MASCOT LX































































































Результаты поиска

Содержание MASCOT LX

Отзывы:

Похожие инструкции для MASCOT LX

Бренды по названию

Популярные бренды

Laars MASCOT LX, Руководство по обслуживанию

Результаты поиска

Содержание MASCOT LX

Отзывы:

Похожие инструкции для MASCOT LX

Бренды по названию

Популярные бренды