Laars MASCOT LX Скачать руководство пользователя страница 34

Страница: 34 / 94

Mascot LX Service Manual

N05 - Domestic hot water sensor not present
This may mean that the sensor is disconnected or not working. If this condition

continues, the controller will present a Lockout message.

• Check for an input on terminals 9 and 10 on the low voltage terminal. If there

is no input, check the domestic hot water temperature sensor and replace it if

necessary. See Section B6.

N06 - Outdoor temperature sensor not present
This may mean that the sensor is disconnected or not working. If this condition

continues, the controller will operate at a setpoint of 140°F or the value of Installer

Parameter P62 (High Setpoint for Heat Curve), whichever is lower.
• Check for an input on terminals 1 and 2 on the low voltage terminal.
• If there is no input, check the outdoor temperature sensor and replace it if nec

essary. See Section B7.

cont.

Notification Codes (continued)

Содержание MASCOT LX































































































Результаты поиска

Содержание MASCOT LX

Отзывы:

Похожие инструкции для MASCOT LX

Бренды по названию

Популярные бренды

Laars MASCOT LX, Руководство по обслуживанию

Результаты поиска

Содержание MASCOT LX

Отзывы:

Похожие инструкции для MASCOT LX

Бренды по названию

Популярные бренды