Laars MASCOT LX Скачать руководство пользователя страница 44

Страница: 44 / 94

Mascot LX Service Manual

The System sensor is mounted in the circulating loop, and provides the input for the

CH (Central Heating) function. This type of sensor can fail in either an “open” or

“shorted” condition, or may become inaccurate.
If the SIT controller detects a problem with the system sensor, it will present a fault

message.
To check the sensor for accuracy, see Section B9.

The DHW sensor is mounted in the DHW loop, and provides the input for the DHW

(Domestic Hot Water) function. This type of sensor can fail in either an “open” or

“shorted” condition, or may become inaccurate.
If the SIT controller detects a problem with the DHW sensor, it will present a “n05”

fault message. For more information, see Section B25 or B27.
To check the sensor for accuracy, see Section B9.

System Sensor

DHW Sensor

The Outdoor sensor is mounted outside the heated space, and provides the input for

the Outdoor Reset function. This type of sensor can fail in either an “open” or “shorted”

condition, or may become inaccurate.
If the SIT controller detects a problem with the Outdoor sensor, the controller will

operate at a setpoint of 140°F or the value of Installer Parameter P62 (High Setpoint

for Heat Curve), whichever is lower.
For more information on Outdoor Reset, see Section B18. To check the sensor for ac-

curacy, see Section B9.
Note - By default, the warm weather shutdown feature is always active when the out-

door sensor is installed.

Outdoor Sensor

Содержание MASCOT LX































































































Результаты поиска

Содержание MASCOT LX

Отзывы:

Похожие инструкции для MASCOT LX

Бренды по названию

Популярные бренды

Laars MASCOT LX, Руководство по обслуживанию

Результаты поиска

Содержание MASCOT LX

Отзывы:

Похожие инструкции для MASCOT LX

Бренды по названию

Популярные бренды