Laars MASCOT LX Скачать руководство пользователя страница 28

Страница: 28 / 94

Mascot LX Service Manual

Many of the most serious trouble conditions on this unit will cause a “lockout,” and

the controller will present a lockout code on the display. Often the lockout code will

take you directly to the cause of the problem. After you have corrected the prob-

lem, press the Reset button to exit from the lockout.

Fig. A2-1 Example of Lockout Screen

E001 – Memory error lockout

There has been a lockout due to a problem with the EEPROM memory in the con-

trol unit.

•  Press the Reset button to try to cancel the lockout.
•  Power down the unit, wait two minutes, then power on the unit again.
•  If this does not restore normal operation, replace the SIT control board.  See

Section B30.

E002 – Fan speed error

There has been a lockout because the fan did not reach normal speed.

• Check for a blockage in the vent.
• Check the wiring to the blower. Disconnect the signal connection to the blower

- the blower should run at full speed. See Section B11. If the blower reaches

full speed, the blower itself is probably OK.

• If the blower does not reach full speed, remove the blower and check for free

movement of the fan. Replace the blower if necessary.

• If the blower moves freely, replace the SIT control board. See Section B30.

Lockout Codes

Содержание MASCOT LX































































































Результаты поиска

Содержание MASCOT LX

Отзывы:

Похожие инструкции для MASCOT LX

Бренды по названию

Популярные бренды

Laars MASCOT LX, Руководство по обслуживанию

Результаты поиска

Содержание MASCOT LX

Отзывы:

Похожие инструкции для MASCOT LX

Бренды по названию

Популярные бренды