Laars MASCOT LX Скачать руководство пользователя страница 73

Страница: 73 / 94

Mascot LX Service Manual

Replacing the SIT Control Board

Fig. B30-3 - Standoffs Supporting Control Board

Remove these screws

Fig. B30-1 - Opening the Lower Front Panel

Fig. B30-2 - Removing the Metal Cover

Standoff

supports

The controller for this unit handles all of the control func-

tions required for normal operation: operating tempera-

ture control, modulation of output (blower speed control),

ignition control, pump control, outdoor reset, high limit

control, and many other functions. This controller has

proven to be very reliable.

A suggestion

If the control system is not operating correctly, please

“check out” all of the other possibilities before you

replace the control board. Most service problems are

caused by the sensors and devices that work with the

controller, or by installation or setup problems. It is very

rare for a problem to be caused by the controller itself.

Programs on the SIT Board and Display:

There are actually

two

copies of the program that

controls this unit - one copy in the display, and an-

other copy in the SIT board. If you replace just the SIT

board, and leave the display in place, the program in

the new “blank” SIT board will be copied over from the

display. In the same way, if you replace just the display,

the program will be copied over from the SIT board.

This means that you do not have to order a special pre-

programmed replacement part. However, if you replace

both

the display and the SIT board,

both

copies of

the program will be lost. In this case, you will have to

specify the serial number of the boiler when ordering

the replacement parts.

Required Tools:

•  Small flat screwdriver
•  Phillips-head screwdriver
•  Needle-nose pliers

Replacement Procedure:

1.  Turn off the power switch on the front of the unit.
2.  Shut off all manual gas valves to the unit.
3.  Remove the lower front panel.
4.  Remove the two screws shown in Fig. B30-1.
5.  The front panel is hinged. Swing it down.

B30

Содержание MASCOT LX































































































Результаты поиска

Содержание MASCOT LX

Отзывы:

Похожие инструкции для MASCOT LX

Бренды по названию

Популярные бренды

Laars MASCOT LX, Руководство по обслуживанию

Результаты поиска

Содержание MASCOT LX

Отзывы:

Похожие инструкции для MASCOT LX

Бренды по названию

Популярные бренды