Laars MASCOT LX Скачать руководство пользователя страница 10

Страница: 10 / 94

Mascot LX Service Manual

Electrical Shock Hazard

Electrical shock can cause severe injury, death or property damage. Only

a professional technician, trained in electrical safety, should work on this

unit. Whenever the troubleshooting procedures make this possible, turn

off the power to the unit before working inside the cabinet. The only ex-

ceptions would be when it is necessary to test the voltages between the

points listed in this manual.
This unit includes the following electrical hazard areas:

Full line voltage is present behind the lower front panel. Be

especially careful when working on the unit if this cover has been

lowered. Always replace the cover when the service procedure is

complete.

Before doing any work inside the unit, disconnect the power supply to

prevent electrical shock or damage to the equipment. It may be neces-

sary to turn off more than one power supply disconnect.
All electrical wiring is to be done in accordance with local codes, or in the

absence of local codes, with: 1) The National Electrical Code ANSI/NFPA

No. 70 - latest Edition, or 2) CSA STD. C22.1 “Canadian Electrical Code

- Part 1.” This appliance must be electrically grounded in accordance

with these codes.

Hot Water Hazard

This unit can produce water which is hotter than 125°F (52°C). This can

cause severe burns instantly or death from scalding. Always shut off the

system and allow it to cool for one hour before opening any pipe connec-

tions that may contain hot water.
Children, disabled and elderly persons are at the highest risk of being

scalded. See the Installation and Operating manual for instructions be-

fore setting the temperature at the Mascot LX unit.
For MLXC units - Adjust the outlet control (DHW setpoint or limit) or use

temperature limiting valves to obtain a maximum water temperature

of 125°F (52°C). Check local codes for details of the required mixing

valves. Instruct all users to feel the water temperature before getting into

the bath or shower.
The Mascot LX unit is protected against over-pressurization. A pressure

relief valve is included with each Mascot LX unit.
The condensate water can be hot, and is also slightly acidic.

Safety Notes (continued)

Содержание MASCOT LX































































































Результаты поиска

Содержание MASCOT LX

Отзывы:

Похожие инструкции для MASCOT LX

Бренды по названию

Популярные бренды

Laars MASCOT LX, Руководство по обслуживанию

Результаты поиска

Содержание MASCOT LX

Отзывы:

Похожие инструкции для MASCOT LX

Бренды по названию

Популярные бренды