Laars MASCOT LX Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 94

background image

Mascot LX Service Manual

12

Operating Displays

Operating Mode Displays -

When the unit is operating normally, use the Up and Down buttons to rotate through the

following functions:
• Outlet temperature - The setpoint for central heat is adjustable. Range 45°F - 189°F,

default 130°F

*  Inlet temperature
•  Delta T (the difference between the outlet and inlet temperatures)
•  Outdoor sensor (if the outdoor temperature sensor is installed
•  Flue temperature
•  Domestic hot water temperature (if this is a Combi model or is connected to an external

tank). The setpoint is adjustable. Range 68°F - 189°F, default 120°F

• System temperature (if a System probe is installed). The setpoint is adjustable. Range

45°F - 189°F, default 130°F.

• Burner rate (if the burner is lit)
You can also use the Up and Down buttons to step through these displays. The following

images show how to interpret these displays.

Operating Modes -

The control system uses four modes:
Operating Mode - While the unit is running, the controller will rotate between several stan-

dard displays.

User Mode -

This mode allows the user to change some of the setpoints. To go to

User Mode, press and hold the OK/Select button for one second.

Installer Mode -

This allows the installer to change all of the parameters used to install

and configure the boiler. To go to the Installer Mode, press and hold

the OK/Select and Down buttons for five seconds. For details, see the

Appendix.

Service Mode -

This mode should only be used by technicians who have been trained

in service procedures on the Mascot LX. For details, see Section C -

“Combustion.”

«
...
16
17
18
19
20
...
»

Содержание MASCOT LX































































































Отзывы:

Нет отзывов

Похожие инструкции для MASCOT LX

Бренд: Raymarine Страницы: 464

Бренд: 3M Страницы: 8

Бренд: ZOLL Страницы: 3

Бренд: Eclipse Combustion Страницы: 46

Бренд: Bard Страницы: 2

Бренд: GE Страницы: 242

Бренд: GE Страницы: 24

Бренд: Balanced Body Страницы: 3

Бренд: Datex-Ohmeda Страницы: 80

Бренд: MacDon Страницы: 2

Бренд: V-TAC Страницы: 6

DISHSTAR ADA-SEER

Бренд: Jackson Страницы: 2

Бренд: Jaga Страницы: 32

Бренд: Launch Страницы: 3

Бренд: Launch Страницы: 43

Бренд: Launch Страницы: 8

Бренд: Launch Страницы: 67

Бренд: Launch Страницы: 55

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды