Laars MASCOT LX Скачать руководство пользователя страница 9

Страница: 9 / 94

Mascot LX Service Manual

Safety Notes

Please read this section before beginning any

troubleshooting procedures.

If the information in this manual is not followed exactly, a fire or ex

plosion may result, causing loss of life, personal injury, or property

damage.

Necessary Training

This product must be installed and serviced by a professional service

technician, qualified and/or licensed in hot water boiler and heater instal-

lation and maintenance. Any changes to safety-related configuration

parameters must only be done by qualified and/or licensed burner/boiler

operators and mechanics.

Carbon Monoxide Hazard

Improper installation and/or operation could create carbon monoxide gas

in flue gases which could cause death, serious injury, or property dam-

age. Improper installation and/or operation will void the warranty.

Fire or Explosion Hazard

Improper configuration can cause fuel buildup and explosion. Improper

user operation may result in death, severe physical injury, or property

damage. Do not store or use gasoline or other flammable vapors and

liquids in the vicinity of this or any other appliance.

What to Do If You Smell Gas

If any odor of gas is detected, or if the gas burner does not appear to be

functioning in a normal manner,

close the main gas shutoff valve

. The

inlet gas pressure to the appliance must not exceed 13” w.c. (3.2 kPa).
• Do not try to light any appliance.
• Do not touch any electrical switch. Do not shut off the power switch.

Do not use any phone in your building.

• Immediately call your gas supplier from a nearby phone. Follow the

gas supplier’s instructions.

• If you cannot reach your gas supplier, call the fire department, your

heating contractor, gas company, or factory representative.

Содержание MASCOT LX































































































Результаты поиска

Содержание MASCOT LX

Отзывы:

Похожие инструкции для MASCOT LX

Бренды по названию

Популярные бренды

Laars MASCOT LX, Руководство по обслуживанию

Результаты поиска

Содержание MASCOT LX

Отзывы:

Похожие инструкции для MASCOT LX

Бренды по названию

Популярные бренды