Laars MASCOT LX Скачать руководство пользователя страница 72

Страница: 72 / 94

Mascot LX Service Manual

The Mascot LX can accept a 0 - 10V DC input so it can

be controlled by a building management system or exter-

nal modulating control. The Mascot can use the 0 - 10V

signal to control modulation or fan speed, outlet tem

perature, or heat demand. The setup for each of these

is slightly different.

External Modulation Enabled -

The external modulation control can be enabled or dis-

abled using Installer mode:

P30

0 - 10V Input Enable/ Disable

External Modulation Scaling -

The maximum and minimum input signal levels can be

set using Installer mode:

P31

BMS Voltage at Minimum

P32

BMS Voltage at Maximum

BMS Controls Modulation (Fan Speed) -

P25

0 - 10V to Power (enabled)

P33

On Threshold Voltage

P34

Off Hysteresis Voltage

P35

BMS Rate at Minimum Voltage

P36

BMS Rate at Maximum Voltage

This is the default 0 - 10VDC configuration. The external

signal directly corresponds to fan speed or boiler power.

In this mode, the call is initiated by the 0- 10V input

based on parameters P33 and P34. The modulation

power can also be scaled using P35 and P36.

BMS Controls Setpoint -

P25

0 to 10V to Power (disabled)

P37

BMS Temperature Setpoint at

Minimum Voltage

P38

BMS Temperature Setpoint at

Maximum Voltage

In this mode, the 0 - 10VDC input directly controls the

boiler’s output temperature. Note that for this setup,

P25 must be disabled.

BMS Initiates Heat Demand -

P26

0-10V BMS Thermostat Demand (disabled)

P33

BMS On Volts

P34

BMS Demand Off Differential Voltage

This arrangement eliminates the need for a separate

T-T call. This allows a heat demand to be created ev-

ery time the 0 - 10V signal exceeds the value set for

P33. The heat demand will remain until the 0 - 10V

signal drops below the value set for P33 minus P34.

B29

External Modulation Control (BMS)

Содержание MASCOT LX































































































Результаты поиска

Содержание MASCOT LX

Отзывы:

Похожие инструкции для MASCOT LX

Бренды по названию

Популярные бренды

Laars MASCOT LX, Руководство по обслуживанию

Результаты поиска

Содержание MASCOT LX

Отзывы:

Похожие инструкции для MASCOT LX

Бренды по названию

Популярные бренды