KYMCO XCITING 500 Скачать руководство пользователя страница 220

Страница: 220 / 349

. CRANKCASE/CRANKSHAFT

13-4

XCITING 500

Cam chain

Inspect the cam chain for cracks or stiff.

CRANKCASE SEPARATION

Remove the parts required for crankcase

separation (page 13-2).

Remove the twelve bolts from left crankcase.

Remove the bolt from right crankcase.

Place the crankcase assembly with the left

side down and separate the right crankcase

from the left crankcase.

Bolt

Bolts

Loosen the bolts in a crisscross pattern in

several steps.

＊

Separate the right crankcase from the left

crankcase while tapping them at several

locations with a soft hammer.

＊

Содержание XCITING 500






























































































































































































































































































































































Результаты поиска

Содержание XCITING 500

Отзывы:

KYMCO XCITING 500, Руководство по обслуживанию, Страница: 220 / 349

Результаты поиска

Содержание XCITING 500

Отзывы: