KYMCO XCITING 500 Скачать руководство пользователя страница 211

Страница: 211 / 349

. A.C. GENERATOR/STARTER CLUTCH

12-3

XCITING 500

ALTERNATOR STATOR

REMOVAL

Remove the right center body cover (page 2-
5).
Remove the exhaust muffler (page 2-15).
Remove water pump (page 6-10).

Remove the fifteen bolts and right crankcase
cover, dowel pins and gasket.

Remove the two pulse coil mount bolts.
Remove the three stator mount bolts,
grommet and the stator from the right
crankcase cover.

INSTALLATION

Install the stator and tighten the stator mount
bolts to the specified torque.

Torque: 12 N•m (1.2 kgf•m, 9 lbf•ft)

Apply sealant to the grommet seating surface
and install it to the cover groove properly.

Install the pulse coil and tighten mount bolts
to the specified torque.

Torque: 12 N•m (1.2 kgf•m, 9 lbf•ft)

Clean the mating surfaces of the right
crankcase and cover.

Install the dowel pins and gasket.
Install the right crankcase cover and tighten
the bolts in a crisscross pattern in 2 or 3 steps.

Right Crankcase Cover

Dowel Pins Gasket

Bolts Pulse Coil

Stator Bolts Grommet

Содержание XCITING 500






























































































































































































































































































































































Результаты поиска

Содержание XCITING 500

Отзывы:

Похожие инструкции для XCITING 500

Бренды по названию

Популярные бренды

KYMCO XCITING 500, Руководство по обслуживанию

Результаты поиска

Содержание XCITING 500

Отзывы:

Похожие инструкции для XCITING 500

Бренды по названию

Популярные бренды