KYMCO XCITING 500 Скачать руководство пользователя страница 173

Страница: 173 / 349

9. CYLINDER/PISTON

9-7

XCITING 500

Measure the connecting rod small end I.D..

Service Limit: 22.06 mm (0.8824 in)

Calculate the connecting rod-to-piston pin
clearance.

Service Limit: 0.06 mm (0.002 in)

CYLINDER/PISTON
INSTALLATION

PISTON RING INSTALLATION

Carefully install the piston rings into the
piston ring grooves with the markings facing
up.

Do not confuse the top and second rings.

To install the oil ring, install the oil ring,
then install the side rails.

Stagger the piston ring end gaps 120° degrees
apart from each other.
Stagger the side rail end gaps as shown.

Be careful not to damage the piston and
rings.

＊

Содержание XCITING 500






























































































































































































































































































































































Результаты поиска

Содержание XCITING 500

Отзывы:

KYMCO XCITING 500, Руководство по обслуживанию, Страница: 173 / 349

Результаты поиска

Содержание XCITING 500

Отзывы: