KYMCO XCITING 500 Скачать руководство пользователя страница 119

Страница: 119 / 349

. COOLING SYSTEM

6-9

XCITING 500

Remove the O-ring from the housing cover.

Remove the thermostat.

INSPECTION

Visually inspect the thermostat for damage.

Heat the water with an electric heating

element to operating temperature for five

minutes.
Suspend the thermostat in heated water to

check its operation.

Replace the thermostat if the valve stays

open at room temperature, or if it respond at

temperatures other than those specified.

Thermostat begin to open:

−

C (176

−

183

Valve lift:

8 mm (0.3 in) minimum at 95

C (203

Thermostat

Thermometer

Thermostat

O-ring

Thermostat

●

Keep flammable materials away from

the electric heating element.

●

Do not let the thermostat or

thermometer touch the pan, or you will

get false readings.

＊

Содержание XCITING 500






























































































































































































































































































































































Результаты поиска

Содержание XCITING 500

Отзывы:

Похожие инструкции для XCITING 500

Бренды по названию

Популярные бренды

KYMCO XCITING 500, Руководство по обслуживанию

Результаты поиска

Содержание XCITING 500

Отзывы:

Похожие инструкции для XCITING 500

Бренды по названию

Популярные бренды