KYMCO XCITING 500 Скачать руководство пользователя страница 127

Страница: 127 / 349

. COOLING SYSTEM

6-17

XCITING 500

WATER TEMPERATURE
SENSOR

REMOVAL

Remove the side body cover (page 2-8)

Disconnect the water temperature sensor

connector.
Remove the water temperature sensor.

INSPECTION

Connect the water temperature sensor to the

ohmmeter and dip it in oil contained in a

pan which is placed on an electric heater.
Gradually raise oil temperature while

reading the thermometer in the pan and the

ohmmeter connected. If the resistance

measured is out of specification, replace the

temperature gauge with a new one.

Temperature

Standard resistance

℃

140

–

310

Ω

115

℃

24.1

–

28.2

Ω

After the water temperature sensor has been

installed, fill coolant and perform air

bleeding (page 6-6).

INSTALLATION

With thread lock applied to the threaded

part, tighten the water temperature sensor.

Torque: 8 N•m (0.8 kgf•m, 5.8 lbf•ft)

●

Handle the water temperature sensor

carefully as it is vulnerable to impact.

●

Do not allow the water temperature

sensor and the thermometer to come in

contact with the bottom of the pan.

＊

Water Temperature Sensor

Thermometer

Water Temperature Sensor

Содержание XCITING 500






























































































































































































































































































































































Результаты поиска

Содержание XCITING 500

Отзывы:

Похожие инструкции для XCITING 500

Бренды по названию

Популярные бренды

KYMCO XCITING 500, Руководство по обслуживанию

Результаты поиска

Содержание XCITING 500

Отзывы:

Похожие инструкции для XCITING 500

Бренды по названию

Популярные бренды