Kusam-meco KM-CAL-907 Скачать руководство пользователя страница 51

Страница: 51 / 76

Step 6:

Pressing the

〔

〕

key saves the adjusted value and the LCD shows “SAVE” symbol in the upper

part for 2 seconds.

Step 7:

Pressing the

〔

ZERO

〕

key exits the CAL mode and back to step 4 for next range, until other range

adjustment is finished.

11.2 Adjusting Frequency

Step 1:

Make sure the lead cables for measurement are not connected to the measuring instrument under

test.

Step 2:

Using the

〔

FREQ

〕

key, select frequency function.

Step 3:

Connect the lead cables to the output terminals of the standard source as shown in Figure 16.

Step 4:

The measured value and unit shall be shown in the upper part of the LCD.

Step 5:

Pressing the

〔

ZERO

〕

key enters the measurement CAL mode. The LCD shows the present adjusting

point “CAL:0” in the lower part and the reference frequency and unit needed for the point in the upper part.

Step 6:

Pressing the

〔

〕

key saves the adjusted value and the LCD shows “SAVE” symbol in the upper

part for 2 seconds.

Step 7:

Pressing the

〔

ZERO

〕

key exits the CAL mode. The adjustment is finished.

Содержание KM-CAL-907













































































Результаты поиска

Содержание KM-CAL-907

Отзывы:

Похожие инструкции для KM-CAL-907

Бренды по названию

Популярные бренды

Kusam-meco KM-CAL-907, Руководство пользователя

Результаты поиска

Содержание KM-CAL-907

Отзывы:

Похожие инструкции для KM-CAL-907

Бренды по названию

Популярные бренды