Kusam-meco KM-CAL-907 Скачать руководство пользователя страница 14

Страница: 14 / 76

Environmental Requirements

Use the instrument in locations that meet the following environmental requirements:

Ambient temperature and humidity

Ambient temperature range: 0 to 50

℃

Ambient humidity range: 20 to 80% RH. Use the instrument under non-condensing condition.

Flat and level locations

Do not use the instrument in locations that are

Exposed to direct sunlight or close to any heat source.

Exposed to frequent mechanical vibration.

Close to any noise source, such as high-voltage equipment or motive power sources.

Close to any source of intensive electric or electromagnetic fields.

Exposed to large amounts of greasy fumes, hot steam, dust or corrosive gases.

Exposed to unstable or a risk of explosion due to the presence of flammable gases.

Note:

Use the instrument under the following environmental conditions if precise source or measurement is your

requirement:

Ambient temperature range: 23

Ambient humidity range: 20 to 80% RH(non-condensing)

Содержание KM-CAL-907













































































Результаты поиска

Содержание KM-CAL-907

Отзывы:

Похожие инструкции для KM-CAL-907

Бренды по названию

Популярные бренды

Kusam-meco KM-CAL-907, Руководство пользователя

Результаты поиска

Содержание KM-CAL-907

Отзывы:

Похожие инструкции для KM-CAL-907

Бренды по названию

Популярные бренды