Kubota 2420 Скачать руководство пользователя страница 7

Страница: 7 / 69

Grounding

Installation

WARNING

Do not connect the ground cable
to the following places:

1. Gas piping

Explosion or fire may occur.

2. Ground cable of lightning

Conductor, or telephone cable.
Electric shock may occur in the

case of lightening.

A clearance of 30 cm minimum

must be provided around the cen-
trifuge.

If the centrifuge is driven into un-
controlled rotations due to a fail-

ure, secondary damage can result

from energy absorbed by the rota-
tion.

Do not install the centrifuge on an

inclined, slippery, or unstable sur-
face.

Violent vibration may occur.

Ensure that the ground cable is

connected to the grounding termi-
nal.

This precaution must be strictly

observed to avoid accidents due
to electric shocks or leakage.

Installation

CAUTION

3. Water pipes

Do not install the centrifuge in a place
with high humidity (relative humidity 85%

or above).
Leak or accident may occur.

Do not install the centrifuge in a place

with poor ventilation.
Otherwise inside temperature of the cen-

trifuge may rise, resulting in accidents.

Do not install the centrifuge in a dusty

place.

Do not install the centrifuge in a
place where the temperature is

below 10

or over 40 .

A place with the ambient tempera-

ture beyond 40

can introduce

undesirable build-up of heat inside

the centrifuge and a place under

can cause the centrifuge

malfunction and, as the result, ac-

cidents.

Lifetime of rotors

Use of rotors beyond the lifetime

may lead to breakage of the rotor.
If the rotor is used continuously

even after the lifetime of the rotor
has expired, should the rotor get

damaged an accident may occur.

City water pipes may not be
adequate as a ground since it

may consist of plastic piping.

Содержание 2420






































































Результаты поиска

Содержание 2420

Отзывы:

Kubota 2420, Инструкция по эксплуатации и обслуживанию, Страница: 7 / 69

Результаты поиска

Содержание 2420

Отзывы: