Kubota 2420 Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 69

Kubota 2420 Скачать руководство пользователя страница 35

４－２

WARNING

Perform a monthly careful inspection of the rotor appearance. Check for
any deformation or damage, including the interior and bottom of the holes.
If any abnormality whatsoever is found, there may be significant damage or
corrosion of the rotor that could lead to serious damage or accidents
involving physical injury. Stop operation at once, put "DO NOT USE" labels
on the rotor and centrifuge lid, and contact your local dealer to arrange for
authorized service.

Motor

Speed control

Rotor and bucket

Imbalance

lid

Electric current

Chamber

Insulation

Speed meter

Install the centrifuge

Timer

４－２．

Monthly Inspections

［１］

Inspect the rotor

［２］

Clean the rotor and buckets

Remove the rotor from the shaft, and clean it.

Refer to Page 4-3

.

［３］

Clean the chamber interior

Refer to Page 4-3

.

４－３．

　

Annual Inspection

Annual Inspection (fee required)

　

For the following inspection items, please call your local dealer and set up an
appointment for a periodical inspection.

Section 4 Service

«
...
33
34
35
36
37
...
»

Содержание 2420






































































Отзывы:

Нет отзывов