Kubota 2420 Скачать руководство пользователя страница 16

Страница: 16 / 69

３－１

If the lid is not closed properly the
centrifuge is not able to start.
Make sure the lid is closed firmly.

NOTE

Install the rotor after checking if the
"Bucket intervention prevention plate" is
installed on the drive shaft.

Refer to page 1-1.

NOTE

Press the "SPEED/TIME" knob to check the "centrifugal force" of the set
speed or "speed" of the set centrifugal force.

NOTE

Contd. on next page.

When using this centrifuge, observe the contents of the Section "General
Notes" being described in the front part of this document and the
precautions given in respective sections.

Section 3

Operation

３－１．

Cautions of Operation

３－２．

Operation

Operation 1.

Turn on the

“

POWER" switch

．

Operation 2

．

After the

“

STOP

”

lamp on the control panel lights, press the

“

OPEN

”

button.

Operation 3.

Mount the rotor on the drive shaft.

Refer to Section 6.

Operation 4.

For swinging bucket rotor

，

mount buckets on the rotor.

Operation 5.

Place the sample in the rotor or buckets

．

Refer to Section 6.

Operation 6.

Close the lid firmly.

Operation 7.

Proceed to

operation 9

when operating with the same setting values as before.

Operation 8.

Set the respective parameters.

・

Set to required speed.

Refer to page 3-6.

・

Set to required time.

Refer to page 3-8.

・

Set braking force during deceleration and acceleration speed with the

“

ACC/DEC

”

key

Refer to page 3-12.

●

When the memory has been saved, press the selection key.

Refer to page 3-10.

Содержание 2420






































































Результаты поиска

Содержание 2420

Отзывы:

Kubota 2420, Инструкция по эксплуатации и обслуживанию, Страница: 16 / 69

Результаты поиска

Содержание 2420

Отзывы: