Kubota 2420 Скачать руководство пользователя страница 18

Страница: 18 / 69

３－３

NOTE

When the rotor has stopped, the

“

STOP" lamp flashes and an sound that informs the end of

the operation is issued.

●

The

“

Sound that informs the end of the operation

”

can be selected from the 5 kinds

＋

Sound none.

Refer to page 3-14.

●

The

“

Alarm Indicators

”

to show the end of the operation can be selected from the 5

kinds.

Refer to page 3-17.

Operation 11.

Press the

“

OPEN" button to open the lid.

“

STOP

”

lamp remains lit.

Operation 12.

Remove the sample.

Refer to page 3-16.

Operation 13.

If the centrifuge is to be used again, return to

Operation 5.

Operation 14.

After finishing use of the centrifuge, turn "OFF" the "POWER" switch to turn off
the power supply, leaving the lid in opened state.

If the power is turned off while a memory being called up and is
then turned on again, the same memory as displayed before the
power cut will be called up and displayed.

Ex. :

Turn off the power while

“

MEMORY 2

”

called up. Turn on the power,

the

“

MEMORY 2

”

key lamp will light and the parameter stored under

“

MEMORY 2

”

key will be displayed.

Section 3 Operation

Содержание 2420






































































Результаты поиска

Содержание 2420

Отзывы:

Kubota 2420, Инструкция по эксплуатации и обслуживанию, Страница: 18 / 69

Результаты поиска

Содержание 2420

Отзывы: