Kubota 2420 Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 69

Kubota 2420 Скачать руководство пользователя страница 29

３－１４

100rpm

×

100 g

×

min

sec

SPEED

TIME

100rpm

×

100 g

×

min

sec

SPEED

TIME

FUNCTION

［３］

Setting the Sound that informs the end of the operation

The

“

Sound that informs the end of the operation

”

can be selected from the 5

kinds

＋

Sound none.

Use this function to identify each

“

Sound that informs the end of the operation

”

when

you use more than one centrifuges.

Factory default :

［

1

］

（１）

Pressing the "SPEED/TIME" knob while holding down the "FUNCTION" key.
The used number of times of the centrifuge is displayed.

（２）

Pressing the "SPEED/TIME" knob several times and let indicate "

"

on the "TIME"

display. The "SPEED" display indicates the current setting of the sound that informs.

Refer to Page 3-11.

[Ex.

］

The

“

Sound that informs the end of the operation

”

１

.

（３）

Turn the "SPEED/TIME" knob to change the "Sound that informs the end of the opera-
tion".
Pressing the "FUNCTION" key makes the selected buzzer sound once.

The "Sound that informs the end of the operation" can be selected from 1, 2,3, 4,
5 of 5 kinds

＋

0 (Sound none).

（４）

Then, press the "SPEED/TIME" knob while holding down the "FUNCTION" key.
The display returns to the previous Speed and Time indication after the setting ( Sound
that informs the end of the operation) is saved.

Section 3 Operation

«
...
27
28
29
30
31
...
»

Содержание 2420






































































Отзывы:

Нет отзывов