Kubota 2420 Скачать руководство пользователя страница 28

Страница: 28 / 69

３－１３

100rpm

100 g

min

sec

SPEED

TIME

100rpm

100 g

min

sec

SPEED

TIME

FUNCTION

［２］

Setting the "SLOW" deceleration

The characteristics have become as shown in the graph.
You can set the natural deceleration starting speed

by the following method.

Factory default

，

it is set as 0 rpm

．

The setting range of "N" is from 0 to 4,000 rpm.

（１）

Pressing the "SPEED/TIME" knob while holding down the "FUNCTION" key.
The used number of times of the centrifuge is displayed.

（２）

Pressing the "SPEED/TIME" knob several times and let indicate "

"on the "TIME"

display.
The "SPEED" display indicates the current setting of the natural deceleration speed.

Unit : rpm

Refer to Page 3-11.

［

Ex.

］　

Setting is the 0 rpm.

（３）

Turn the "SPEED/TIME" knob to set the natural deceleration speed.

The setting range of "N" is from 0 to 4,000 rpm.

［

Ex.

］

Setting the 300 rpm.

（４）

Press the "SPEED/TIME" knob while holding down the "FUNCTION" key.
The display returns to the previous Speed and Time indication after the setting ( Natural
deceleration speed) is saved.

Section 3 Operation

Ｎ

１０００

Ｎ

１０００

（Ａ）Ｎ＝

1,000 rpm or more

（Ｂ）Ｎ＝

1,000 rpm or less

ｒ

ｐｍ

ｒ

ｐｍ

speed

It changes to the SLOW
characteristic from RAPID

at 1000rpm.

RAPID

Natural

deceleration

SLOW

TIME

speed

RAPID

Natural

deceleration

Содержание 2420






































































Результаты поиска

Содержание 2420

Отзывы:

Kubota 2420, Инструкция по эксплуатации и обслуживанию, Страница: 28 / 69

Результаты поиска

Содержание 2420

Отзывы: