KTM 950 ADVENTURE 2003 страница 99 Скачать руководство пользователя

Страница: 99 / 160

9-2

Repair manual KTM LC8

Art.-Nr

. 3.206.009-E

ERROR

Engine does not start when
the starter button is actuated

Engine only switches on
when the clutch lever is
pulled

Engine switches on although
a gear is engaged

Engine switches on but does
not start

Engine does not have
enough power

Engine gets too hot

CAUSE

Operating error

Battery is dead

IGNITION fuse is blown

Main fuse is blown

Ignition lock or emergency OFF
switch is defective

Back-up starter system is defective

Operating error

Fuel pump hose is blown

Plug and socket connector on the
wiring harness is oxidizing

Fuel supply partly interrupted

Carburetors are leaking

Air filter is heavily soiled

Ignition curve for 80 octane is
activated

Not enough coolant in the cooling
system

Radiator fins are heavily soiled

Formation of foam in the cooling
system

Kinked or damaged radiator hose

Thermostat defective

Fan fuse is blown

Fan or thermoswitch for fan is
defective

REMEDY

Switch on the ignition, switch the transmission to neutral,
switch on the emergency OFF switch

Charge battery and look for cause of discharging; replace
defective parts

Replace the IGNITION fuse in the fuse box

Remove the right engine cowl and replace the main fuse in
the starter relay

Check the ignition lock and emergency OFF switch, replace
any defective parts

Repair the back-up starter system

Open the fuel taps, refuel, do not pull the chock, follow the
starting instructions

Replace the FUEL PUMP fuse

Remove the covering and the fuel tank, clean the plug and
socket connector and treat with contact spray

Check the fuel taps, run the fuel lines without kinks

Check the vacuum hoses and vent hoses for a tight fit kink-
free installation

Replace the air filter

Activate the ignition curve for 95 octane, provided 95 octane
fuel is being used

Add cooling liquid (see maintenance work), check the cooling
system for leakage

Clean the radiator fins with a water jet

Replace the cooling liquid, use brand-name antifreeze

Install the radiator hose correctly or replace

Have the thermostat checked (opening temperature 75°C) or
replaced

Replace the FAN fuse

Replace defective parts

Содержание 950 ADVENTURE 2003

































































































































































Результаты поиска

Содержание 950 ADVENTURE 2003

Отзывы:

Похожие инструкции для 950 ADVENTURE 2003

Бренды по названию

Популярные бренды

KTM 950 ADVENTURE 2003, Руководство пользователя

Результаты поиска

Содержание 950 ADVENTURE 2003

Отзывы:

Похожие инструкции для 950 ADVENTURE 2003

Бренды по названию

Популярные бренды