KTM 950 ADVENTURE 2003 Скачать руководство пользователя страница 46

Страница: 46 / 160

Piston and cylinder identification

The cylinder size

is impressed in the bottom of the cylinder near the

chain tunnel; 1 is size I, 2 is size II.

The piston size

is impressed in the top of the piston; 1 is size I, 2 is

size II.

Assembling the cylinder head

– Slide the valve spring washers

over the valve guides and mount

new valve shaft seals

– Lubricate the valve shafts and insert the valves in their original

position in the valve guides.

NOTE: a washer (14x30x2) is located under the spring retainers for the
exhaust valve springs to increase the spring preload.

– Mount the inner and outer valve springs

with the spring retainers

and compress the springs using the valve assembling tool

(590.29.019.000 with the attachment 600.29.041.000).

– Grease the valve spring keys

and position on the valve shafts.

Relieve the valve springs.

– Tap the valve spring retainers to set the keys.

5-11

Содержание 950 ADVENTURE 2003

































































































































































Результаты поиска

Содержание 950 ADVENTURE 2003

Отзывы:

KTM 950 ADVENTURE 2003, Руководство пользователя, Страница: 46 / 160

Результаты поиска

Содержание 950 ADVENTURE 2003

Отзывы: