KTM 950 ADVENTURE 2003 страница 17 Скачать руководство пользователя

Страница: 17 / 160

3-7

Refitting the engine

– Before mounting the engine, attach the water, SLS and vacuum hoses

(Öttiger clamps - special pliers 600.29.057.000 or spring-loaded
band-type clamps - special pliers 600.29.057.100)

– Position the swing arm and fix with the swing arm pivot on the right

and a suitable pipe on the left.

– Lift the engine into the frame with the trolley jack, insert the sealing

washer in the rear exhaust flange and secure with copper paste if
necessary.

– Guide the chain along the side of the pinion and insert the swing arm

pivot

, screw on the nut but do not tighten yet.

– Insert the bolt

in the lower support (raise or lower the engine

slightly if necessary).

– Remove the trolley jack attachment 600.29.055.100 from the engine.

– Plug the connector on the oil pressure switch

, the temperature

sensor

and the front and rear ignition coil

. Use cable clips to

fasten the wiring harnesses.

– Screw on the ground wire connection

– Attach the pulse generator connector

– Position the foot brake pedal, apply Loctite 243 to the bolt

and

tighten to 25 Nm.

Содержание 950 ADVENTURE 2003

































































































































































Результаты поиска

Содержание 950 ADVENTURE 2003

Отзывы:

Похожие инструкции для 950 ADVENTURE 2003

Бренды по названию

Популярные бренды

KTM 950 ADVENTURE 2003, Руководство пользователя

Результаты поиска

Содержание 950 ADVENTURE 2003

Отзывы:

Похожие инструкции для 950 ADVENTURE 2003

Бренды по названию

Популярные бренды