KTM 950 ADVENTURE 2003 страница 106 Скачать руководство пользователя

Страница: 106 / 160

10-6

Repair manual KTM LC8

Art.-Nr

. 3.206.009-E

Replacing the steering head bearing

– Dismount the fork legs (see page 10-4).

– Unscrew the brake hose guides from the top and bottom triple clamp.

– Remove the handlebar clamps

and lay the handlebar back.

NOTE: if the tanks and the tank compartment have not been removed,
protect these parts from being damaged.

– Loosen the clamp bolt on the steering stem

, remove the blind bolt

on the steering stem, holding the bottom triple clamp

prevent it from sliding out of the steering head.

– Remove the top triple clamp

and pull the bottom triple clamp

and the steering stem down and out of the steering head.

– Remove the protective ring

, seal

and the upper steering head

bearing

– Pull the lower steering head bearing

off of the steering stem with a

suitable puller and remove the seal

– Slide on a new seal and a new steering head bearing on the steering

stem with a suitable tube.

CAUTION

HEN YOU PRESS IN THE BEARING

MAKE SURE TO PRESS THE INNER RING ONLY

. I

YOU PRESS IN THE OUTER RING

THE BALLS OR THE BEARING SURFACES OF THE BALLS

WILL BE DAMAGED

– Insert the special tool 584.29.092.000 with the collet 584.29.089.000

into the steering head from below and drive the outer ring

on the

upper steering head bearing out of the steering head.

– Insert the special tool 584.29.092.000 with the collet 584.29.089.000

into the steering head from above and the drive the outer ring

the lower steering head bearing out of the steering head.

– Drive the new outer ring on the upper steering head bearing

into

the steering head using the special tool 584.29.091.000 with the
collet 584.29.089.000.

– Drive the new outer ring on the lower steering head bearing

into

the steering head using the special tool 584.29.091.000 with the
collet 584.29.089.000.

NOTE: make sure the outer bearing rings do not cant when they are
driven in.

Assembly is in the reverse order as disassembly.

To adjust the play of the steering head bearing, see page 12-13.

Tighten the clamp bolt on the steering stem and the collar bolts on the
top triple clamp to 23 Nm; tighten the collar bolts on the bottom triple
clamp to 18 Nm.

Tighten the collar bolts on the handlebar clamps to 20 Nm.

Secure the AH bolts on the upper brake hose guide with Loctite 243 and
tighten to 8 Nm.

To mount the fork legs, see page 10-4.

Содержание 950 ADVENTURE 2003

































































































































































Результаты поиска

Содержание 950 ADVENTURE 2003

Отзывы:

Похожие инструкции для 950 ADVENTURE 2003

Бренды по названию

Популярные бренды

KTM 950 ADVENTURE 2003, Руководство пользователя

Результаты поиска

Содержание 950 ADVENTURE 2003

Отзывы:

Похожие инструкции для 950 ADVENTURE 2003

Бренды по названию

Популярные бренды