KTM 950 ADVENTURE 2003 страница 29 Скачать руководство пользователя

Страница: 29 / 160

Water pump

– Remove the water pump cover

, discard the O-ring gasket.

NOTE: also remove the 2 dowel pins used to keep the water pump cover
in a central position.

– Hold the water pump wheel with special tool 600.29.082.000,

remove the bolt

and pull the water pump wheel

off of the

shaft.

NOTE:
– The bolt and the water pump wheel only need to be removed if the

water pump will be serviced. They do not need to be removed if you
are only dismounting the clutch cover.

– If the water pump wheel cannot be removed because it is being held

by residual thread adhesive, the water pump shaft and the water
pump wheel can be pressed out from the inside later.

CAUTION

F YOU TRY TO LOOSEN THE BOLT ON THE WATER PUMP WITHOUT USING SPECIAL

TOOL

600.29.082.000,

YOU MAY BREAK THE DRIVER ON THE BALANCER SHAFT OR

WATER PUMP SHAFT

Oil screen

– Remove the oil screen cover

– Carefully pull the oil screen

out of the clutch cover with a pair of

pliers.

Clutch cover

– Remove the bolts and detach the inner clutch cover together with the

outer clutch cover. Be careful not to lose the dowel pins.

NOTE:
– The outer clutch over can remain on the inner clutch cover if you also

remove the bolt

on the outer clutch cover.

– If the case bolt for the blocking hole is still mounted, it must also be

removed.

4-8

Repair manual KTM LC8

Art.-Nr

. 3.206.009-E

Содержание 950 ADVENTURE 2003

































































































































































Результаты поиска

Содержание 950 ADVENTURE 2003

Отзывы:

Похожие инструкции для 950 ADVENTURE 2003

Бренды по названию

Популярные бренды

KTM 950 ADVENTURE 2003, Руководство пользователя

Результаты поиска

Содержание 950 ADVENTURE 2003

Отзывы:

Похожие инструкции для 950 ADVENTURE 2003

Бренды по названию

Популярные бренды