KTM 950 ADVENTURE 2003 страница 20 Скачать руководство пользователя

Страница: 20 / 160

3-10

Repair manual KTM LC8

Art.-Nr

. 3.206.009-E

– Screw on the radiator together with the fan and the radiator shield

, tighten the bolts to 10 Nm.

– Connect the water hoses on the radiator (special pliers

600.29.057.100)

– Attach the electric connections for the fan motor and the temperature

switch

– Screw the rear exhaust manifold on to the cylinder head.
– Insert the front exhaust manifold in the rear exhaust pipe, mount to

the front cylinder head together with the sealing washer and tighten
the exhaust nuts

NOTE: the exhaust nuts should be tightened evenly without bending the
metal sheet.

– Tighten the exhaust clamp

on the front manifold.

– Mount the lower air filter box on the intake ports, connect the drain

hose and push the fuel hose and the cable for the idle speed
adjustment down through the opening in the lower air filter box.

CAUTION

–

MAKE SURE THERE ARE NO KINKS IN THE CARBURETOR VENT HOSES AND RUN
THEM DOWN BEHIND THE STARTER ENGINE WITHOUT FORMING AN UPWARD
ARCH

–

REMOVE THE CLOTH USED TO COVER THE INTAKE PORTS

– Mount the EPC valve

on the lower air filter box and connect.

– Mount the secondary air system valve

on the lower air filter box,

connecting the thin hose to the intake manifold and the thick hose
directly to the valve.

– Attach the carburetor connection boots to the intake manifold.

NOTE: the clamps on the carburetor connection boots must be aligned
so that they can be tightened through the openings in the side covers.

– Connect the fuel hoses to the carburetors.

NOTE: to make it easier to connect the fuel hoses, disconnect the fuel
hose from the connecting piece (on the side of the engine brace) and
pull the fuel hose up. Reconnect after mounting the carburetor.

– Insert the carburetor in the carburetor connection boots, tighten the

clamps on the carburetor connection boots and screw both side
covers on the lower air filter box.

– Connect both vent hoses to the carburetors and fasten the choke

cable

with a cable clip (see photo).

– Insert the EPC hoses

in the corresponding openings in the lower air

filter box and connect to the carburetors.

– Mount the air filter, position the intake trumpet

and turn in a

counter-clockwise direction.

– Mount the intake snorkel

with the frame to the filter housing.

– Screw on the upper air filter box half. Connect the vent hose and the

EPC hose.

Содержание 950 ADVENTURE 2003

































































































































































Результаты поиска

Содержание 950 ADVENTURE 2003

Отзывы:

Похожие инструкции для 950 ADVENTURE 2003

Бренды по названию

Популярные бренды

KTM 950 ADVENTURE 2003, Руководство пользователя

Результаты поиска

Содержание 950 ADVENTURE 2003

Отзывы:

Похожие инструкции для 950 ADVENTURE 2003

Бренды по названию

Популярные бренды