KTM 950 ADVENTURE 2003 страница 51 Скачать руководство пользователя

Страница: 51 / 160

5-16

Repair manual KTM LC8

Art.-Nr

. 3.206.009-E

General information on servicing the transmission

– Clamp the main shaft in the vise (use protective jaws) and remove the

gears.

– Clean and check all parts.

Use new lock rings whenever you repair the transmission.

Check the tooth profile on the transmission shafts and sliding gears for
wear.

Place the sliding gears on the transmission shafts and check whether
they run smoothly on the teeth.

Check the bearing positions on the transmission shafts.

Mount the idler gear with bearings on the transmission shaft and check
for clearance.

Check the needle bearings in the idler gears.

Assembling the main shaft

– Clamp the main shaft in the vise (use protective jaws) with the gear

facing down.

– Mount the needle bearing

and slide the 5th gear idler

over the

needle bearing with the claws pointing up.

– Mount the stop disk

(28.3 x 35.75 x 1.5 mm) and the lock ring

with the sharp edge facing up.

– Mount the 3rd and 4th gear sliding gear

with 4th gear (larger

outer diameter) facing down.

– Mount the stop disk

(22.2 x 30,2 x 1.5 mm).

– Slip on the needle bearing

and slide the 6th gear idler

over the

needle bearing with the claws pointing down.

– Slip on the 2nd gear fixed gear

with the collar facing down and

mount the stop disk

(20.2 x 28 x 1.5 mm).

Check all gear wheels for smooth operation.

Содержание 950 ADVENTURE 2003

































































































































































Результаты поиска

Содержание 950 ADVENTURE 2003

Отзывы:

Похожие инструкции для 950 ADVENTURE 2003

Бренды по названию

Популярные бренды

KTM 950 ADVENTURE 2003, Руководство пользователя

Результаты поиска

Содержание 950 ADVENTURE 2003

Отзывы:

Похожие инструкции для 950 ADVENTURE 2003

Бренды по названию

Популярные бренды