KTM 950 ADVENTURE 2003 страница 59 Скачать руководство пользователя

Страница: 59 / 160

6-5

– Position the pin and spring in the shifting drum. Mount the gear

sensor

with 2 M5x10 bolts. Tighten bolts to 4 Nm.

– Slide in a new oil filter and mount the oil filter cover

with a new

gasket. Tighten M5x16 bolts to 6 Nm.

– Insert the crankshaft in the friction bearing.
NOTE:
– The crankshaft and the thread for the primary pinion bolt connection

must point down.

– The conrod for the rear cylinder

must face up. Both conrods should

be in the position shown in the illustration.

– Mount the case dowel pins and put a new case gasket in place.

Case half

– Slide the protective sleeve 600.29.005.000 over the countershaft.
– Slip on the generator-end case half. Tap lightly on the countershaft

with a rubber hammer if necessary.

CAUTION

O NOT TRY TO DRAW THE TWO CASE HALVES TOGETHER WITH THE CASE BOLTS

– Screw in all HH case bolts (see illustration for bolt

lengths) and tighten to 10 Nm.

NOTE: the bolts should be tightened in the order
shown in the illustration (numbers in parentheses).

– Move the case into a horizontal position with the

generator side facing up.

M6x65(19)

M6x65(20)

M6x65(21)

M6x90(2)

M6x90(3)

M6x90(4)

M6x40(5)

M6x40(6)

M6x40(7)

M6x90(1)

M6x40(8)

M6x60(9)

M6x60(10)

M6x60(11)

M6x60(13)

M6x75(14)

M6x60(15)

M6x65(16)

M6x65(17)

M6x65(18)

M6x75(12)

Содержание 950 ADVENTURE 2003

































































































































































Результаты поиска

Содержание 950 ADVENTURE 2003

Отзывы:

Похожие инструкции для 950 ADVENTURE 2003

Бренды по названию

Популярные бренды

KTM 950 ADVENTURE 2003, Руководство пользователя

Результаты поиска

Содержание 950 ADVENTURE 2003

Отзывы:

Похожие инструкции для 950 ADVENTURE 2003

Бренды по названию

Популярные бренды