KTM 950 ADVENTURE 2003 Скачать руководство пользователя страница 41

Страница: 41 / 160

5-6

Repair manual KTM LC8

Art.-Nr

. 3.206.009-E

Replacing the supporting bearings in the clutch cover

– Pull the bearing shells out of the clutch cover using the puller

151.12.017.000 and the internal extractor 600.29.018.000

– Measure the diameter of the bearing pin at 3 points that are 120°

apart using a micrometer gauge.

Diameter of the supporting bearing pin: 27.985 mm – 28.000 mm

NOTE: The crankshaft must be replaced if the measurement falls short of
the minimum diameter or if the crankshaft is worn.

– Center the new bearing shells with the assembling sleeve

600.29.046.028

. The assembling sleeve is beveled on one side so

the bearing shells can be pushed in easily. The bearing shells should
protrude 1-2 mm on the other side of the assembling sleeve to make
it easier to position them in the clutch cover.

– Place the bearing shells on the clutch cover with the assembling

sleeve and press in the bearing shells to the stop using the press
mandrel 600.29.046.028

Содержание 950 ADVENTURE 2003

































































































































































Результаты поиска

Содержание 950 ADVENTURE 2003

Отзывы:

KTM 950 ADVENTURE 2003, Руководство пользователя, Страница: 41 / 160

Результаты поиска

Содержание 950 ADVENTURE 2003

Отзывы: