KLS Martin Independant IDP 401 Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 116

background image

Mounting Instructions

Suspension Arm Systems Independant

20

Revision 1

1.4

Warranty

Our Standard Terms and Conditions of Sale effective at the time shall apply. Agreements
diverging from these Standard Terms and Conditions do not restrict the legal rights of the
buyer.
Any warranty exceeding the above provisions shall require a contractual form and shall exclude
component-related vandalism, software updates and consumables.

Important Notices
The product may only be repaired by Gebrüder Martin or a qualified person or firm expressly
authorized by Gebrüder Martin to perform such work.
If the repair is carried out by a person or firm specially authorized by Gebrüder Martin, the
operator of the product is required to obtain from the repairer a certificate with details about
the nature and scope of the repair work done. This certificate must show the date of the repair
and the details of the person or firm carrying out the work and must be signed.
In all cases where a party other than the product manufacturer performed the work, repaired
products must be additionally marked with the repairer’s ID label.
Improper interventions or alterations performed by third parties during the period of limitation
shall void any and all warranty claims. Performing unauthorized actions on the product is
strictly prohibited at any time. Non-compliance will void any liability claim against
Gebrüder Martin.
Gebrüder Martin guarantees the safety and functional capacity of the system only if an initial
commissioning is carried out and the device is approved for operation with a declaration of
handover.

1.5

User’s Inspection

•

Immediately upon receipt, the goods must be checked for completeness and potential
damage in transit.

•

Notice of any such damage must be given immediately.

«
...
18
19
20
21
22
...
»

Содержание Independant IDP 401





















































































































Отзывы:

Нет отзывов

Похожие инструкции для Independant IDP 401

Бренд: Rath Страницы: 3

Бренд: NEC Страницы: 54

Бренд: JB-Lighting Страницы: 40

Бренд: Warehouse-lighting Страницы: 3

Бренд: Eagle Group Страницы: 8

Бренд: E2S Страницы: 5

Бренд: Harken Страницы: 4

Бренд: Harken Страницы: 2

TERRA FORCE BOOM

Бренд: Hardi Страницы: 40

Бренд: Harken Страницы: 4

QuickSlide HemaPRO

Бренд: Hardy Diagnostics Страницы: 2

Бренд: Hardt Страницы: 2

Бренд: Quivogne Страницы: 13

Synthesis SDEC-3000

Бренд: JBL Страницы: 24

Бренд: Xilica Audio Design Страницы: 30

Бренд: Oakworks Medical Страницы: 28

Бренд: Omlet Страницы: 2

Бренд: Omicron Страницы: 382

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды