Kinova Link 6 Скачать руководство пользователя страница 62

Страница: 62 / 296

EN UG-020 Link 6 user guide r1.0

SF03 Joint position monitoring

What does SF03 monitor?

SF03 monitors the positions of each joint and compares the positions with the limits set in the

Joint Limits

Position Limits

page.

Cause of the trigger

Certain trajectories may inadvertently make a single joint rotate constantly in the same direction

without unwrapping. It is most common with the last joint. The unidirectional rotation may

also happen when operating in Automatic and Recovery modes. It results in a

stop category

protective stop.

Remedy

Clear the associated fault.

Identify which joint is nearing its position limit.

Move that joint in the position opposite to its limit.

Launch the

Jog Angular

panel and check the current joint positions.

Adjust the trajectory that caused the fault so that the joint unwraps before it reaches the limit.

Related topics

Joint limits

on page 67

Operating modes

on page 99

Mode: Manual Jog

on page 100

List of safety functions

on page 52

Status of safety functions

on page 222

SF04 Joint speed monitoring

What does SF04 monitor?

SF04 monitors the speed of each joint and compares the speeds with the limits set in the

Joint

Limits

Speed Limits

page.

Cause of the trigger

• Unforeseen environmental forces could cause parts of the robot to exceed the speed planned

for its trajectory. The unforeseen forces, such as a collision with a wall, may cause the

actuators

backdrive

• It can also be caused when the robot is in Monitored Stop when an external force is applied to

it.

It results in a

stop category

2 protective stop.

Remedy

Resume the trajectory. Link 6 has built-in functions to saturate its speed limits automatically.
If the error is triggered consistently, consider modifying the trajectory.

Related topics

Joint limits

on page 67

+1 514-277-3777

kinovarobotics.com

Содержание Link 6






































































































































































































































































































Результаты поиска

Содержание Link 6

Отзывы:

Похожие инструкции для Link 6

Бренды по названию

Популярные бренды

Kinova Link 6, Руководство пользователя

Результаты поиска

Содержание Link 6

Отзывы:

Похожие инструкции для Link 6

Бренды по названию

Популярные бренды