KG ELS-304 Скачать руководство пользователя страница 77

Страница: 77 / 80

ELS-304

Maintenance/Calibration

10-1

10. Maintenance/Calibration

Executing the pre-scheduled Maintenance and Calibration would be highly suggested for

long use.

10.1

Cleaning

To clean this product, use a soft or wet cloth.

Before you clean this product, power this product off and disconnect the power plug.

・

Please do NOT use any organic solvent capable of changing the nature of the
plastic such as benzene or acetone.

・

Please pay attention that any liquid should not be penetrated into this product.

10.2

Fuse Exchange

This product has the power Fuse, and exchange it according to the following procedure.

・

Never fail to turn off the power of this product, and disconnect the plug of the AC
Power Cable.

・

To avoid the fire or electronic shock, the Fuse that will be used in the product

should have the safety standard in the area of the region you use. Any use of
improper Fuse or shorting the Fuse holder would be extremely dangerous and

would be strictly prohibited.

・

Before exchanging the Fuse, if there are abnormal odor or abnormal noise,

please stop using immediately and ask for the repair.

CAUTION

WARNING

Содержание ELS-304

















































































Результаты поиска

Содержание ELS-304

Отзывы:

Бренды по названию

Популярные бренды

KG ELS-304, Руководство по эксплуатации

Результаты поиска

Содержание ELS-304

Отзывы:

Бренды по названию

Популярные бренды