KG ELS-304 Скачать руководство пользователя страница 26

Страница: 26 / 80

ELS-304

3-4

Name and Function of Each Part

(2) GP-IB Connector

This connector conforms to IEEE488.1. You can control this product from a general
GP-IB Controller.

(3) USB Connector

This is a connector to connect a personal computer. Conforming to the USB1.1

Standards, this product can be controlled from a personal computer easily via USB by
Using the attached device driver and control library.

Refer to “

8. Programming Mode

” for more detailed information.

(4) AC Inlet

This is the AC inlet allowing the Volt. Input between 100V and 240V (Worldwide).

(5) Air outlet

This is to exhaust the air taken through the Inlet on the Front Panel to cool this product

by the air.
Do not put an obstacle to block the airflow nor install this product in a small and

enclosed place.

(6) Ext. Control Input BNC Connector

For inputting external Voltage for controlling load level. The input range is 0-10V.
For more information, refer to

→

“

5.9 External Control (EXT) Mode

”.

3.3

Side Panel

(1) Air inlet

To take air for cooling

Do not put an obstacle to block the airflow.

(2) Handle

Please grasp this handle when you carry this product.

(1)

(2)

Содержание ELS-304

















































































Результаты поиска

Содержание ELS-304

Отзывы:

Бренды по названию

Популярные бренды

KG ELS-304, Руководство по эксплуатации

Результаты поиска

Содержание ELS-304

Отзывы:

Бренды по названию

Популярные бренды