KG ELS-304 Скачать руководство пользователя страница 3

Страница: 3 / 80

ELS-304

For your safety use of this Product

For your safe use of this Product

This section describes the Handling Instructions when you use this Product in safety.

You are requested to understand and follow these instructions without fail.
It is not our responsibility for any accidents caused by the ignorance of the instructions or

improper handling or operation. .

Disassembly

There are some portions inside where high Voltage may

present and which is dangerous to human. Please do NOT

remove the cover or panel of this Product.

Surroundings

For the safety, do not use this product where explosive or

corrosive gas can be detected.

If you use this Product in the strong electromagnetic field,
because of the characteristics of this product, the noise induced

on the input cable may be also regarded as the signal and

measured to affect the measurement result. Do not use in such
surroundings.

Please do not palace this product where it will be subject to direct

sunlight or high temperature.

Please follow the instruction to use this product in the

temperature range between 23

℃±

℃

and the temperature of

70% or less.

When any condensation is present, please do not use this product

until completely dried.

Please do not use this product in a dirty, duty, stuffy, slanting, or
vibrating locations. This product has a forced air-cooling

functions, so do not block the inlet and outlet by an obstacle and

keep the enough space around this product for the air-cooling.

Содержание ELS-304

















































































Результаты поиска

Содержание ELS-304

Отзывы:

Бренды по названию

Популярные бренды

KG ELS-304, Руководство по эксплуатации

Результаты поиска

Содержание ELS-304

Отзывы:

Бренды по названию

Популярные бренды