KG ELS-304 Скачать руководство пользователя страница 51

Страница: 51 / 80

ELS-304

Alarm

7-1

Alarms

The protection functions and alarms of this product are described.

When an Alarm occurs, beep sound rings, an error message is displayed, and the Load will
promptly be set OFF to the no-load condition.

7.1

Over Current Limit

When this alarm works, the Load Current is limited to protect the Load section of this

product. The Lord Current will be limited by the 110% of the Current Limit Vale. To

setup the Current Limit, refer to “

5.4

Curr. limit setting

”.

If the Current limit is not setup, the Current Limit value will be 120A as the default

value.

7.2

Over Voltage Alarm

When the load volt exceeds the tolerance value, this alarm operates.
In High range, when Vin

≧

31.2V(Typ), in Low range when Vin

≧

4.16V(Typ) this alarm

is issued.

Fig.7-2-1

Display of Over Voltage Alarm

・

This is for the alarm only, there is no protection for the Load Section of this
product.

・

When this alarm works, if there is questionable odor or abnormal noise, please

stop using this product immediately and call us or our distributor for the repair

WARNING

Содержание ELS-304

















































































Результаты поиска

Содержание ELS-304

Отзывы:

Бренды по названию

Популярные бренды

KG ELS-304, Руководство по эксплуатации

Результаты поиска

Содержание ELS-304

Отзывы:

Бренды по названию

Популярные бренды